Sandustry Tips & Tricks: Copy, Grabber, Fluid & Filters
Four small habits with outsized payoff — duplicate repeated structures with copy-paste, level the Grabber early, split fluids into their own lines, and let Filters isolate byproducts.
Four habits that quietly separate a smooth first factory from a messy one. If you are just starting out, pair this with the Sandustry Beginner Guide for the full progression path.
Copy-Paste Repeated Structures
Select a structure with C, then duplicate whole sections using Ctrl+C and
Ctrl+V. Any layout you build twice by hand is a layout you should have
copied the first time.
Level Up the Grabber Early
The official Beginner's Guide calls this out explicitly: improve the Grabber early. Until your factory is fully automated, you will be hauling material by hand more often than you expect, and a stronger Grabber makes every one of those trips cheaper.
Give Each Fluid Its Own Lines
Pipes happily carry several fluid types at once — the problem appears at the end. A Liquid Vent cannot choose which fluid it releases, so shared lines eventually spit out the wrong liquid in the wrong place. Separate fluid networks stay predictable.
Let Filters Deal With Byproducts
Whenever one production line carries several materials at once, Filters are the tool that pulls a specific output out of the stream. Shaker lines with their Residue-plus-Gold output are the classic case.
For the machine behind that chain, see the Shaker in the database.
Run a Conveyor Belt Straight From Machine Output
When a machine's output backs up — lava tower or smelter choking on its own residue — lay a single Conveyor Belt from the machine outlet all the way to the receiving factory. The belt clears the pile and feeds the next step without requiring splitters, redirectors, or rethinking the whole layout.
Note — This is a quick-fix habit, not a replacement for a well-planned logistics network. If a single belt solves a chronic blockage, the belt itself is the fix; if the blockage returns after rerouting, revisit the upstream design.
Keybinds Worth Memorizing
The following key combinations can streamline your factory building workflow (来源 1,核查 2026-09-23).
| Key | Action |
|---|---|
| C | Hold to select and drag structures |
| X | Click and drag to remove blocks |
| Ctrl | Build over existing structures |
| Alt | Reverse direction for items like Conveyor Belts |
| 5 | Place a copy after holding selection |
| F | Activate picker tool |
| V | Activate ruler tool |
| X | Delete selected item |
Blueprint copying works by holding a selection, pressing 5, then placing the duplicate (具体机制主播未解释,页面表述保留操作层即可).
Four Filter Recipes From a Real Run
These filter configurations come from an actual gameplay session (来源 1,核查 2026-09-23).
Recipe 1: Separate Dry Sand Setting the filter to Sand drops undried sand while letting wet sand pass through. This keeps only processed material flowing.
Recipe 2: Return Unburnt Residue Filter out regular residue and send it back to the burning area for recycling instead of letting it accumulate.
Recipe 3: Isolate Gold Output Configure the filter to drop Gold while other materials continue on the belt. Gold falls down to be collected separately.
Recipe 4: Separate Seeds Add a filter specifically for Seeds to keep them stored apart from other production materials.
Tip — When setting filter direction, first decide which material should drop, then choose whether to allow or block each material. Reversed filter direction is a common mistake. Use Launcher to return under-processed residue for reburning and prevent buildup.
Reverse Filter Mode
The usual approach is to tell a Filter exactly which item to let through and block everything else (来源 1,核查 2026-09-26). There is an equally valid opposite approach: tell it to let everything through and block only one item. This reverse configuration works best when you have a multi-material line and need to remove a single contaminant.
Example: recovering a clogged Seed storage line. When a Filter built to allow only Seeds became bottlenecked, the fix was not to rebuild the filter but to flip its logic — configure it to let every material pass while blocking only Gold. The line was first set up incorrectly twice (allowing the wrong item, and forgetting Gold entirely), but once correctly configured, it ran clear again. The constraint had shifted from "select the one good item" to "remove the one bad item." The same pattern applies whenever a single material is the outlier in a mixed stream.
Tip — After setting any Filter, verify the direction you intended matches what actually flows. A common slip is toggling allow/block on the wrong material, or forgetting to add the target item to the opposite side. A quick check right after placement prevents a full line stoppage.
Advanced Filters: A Smarter Pick and a Compact Seed Separator
When the tier 4 uplink opens up, the choice comes down to the Rocket Launcher or the Advanced Filter — and in this run the weapon was skipped outright, because the filter was judged the far more valuable investment (来源 1,核查 2026-09-26).
Throughput backs that call up: Advanced Filters move material slightly faster than regular Filters, so the upgrade pays off in speed as well as in what it can do (来源 1,核查 2026-09-26).
The payoff this run showcases is an ultra-compact seed separator. The recipe is short — set the Advanced Filter to block Water, team it with a Clearing Frame and a Liquid Vent, and configure it so only Seed and Wood Seed are allowed through (来源 1,核查 2026-09-26).
Put to the test, the setup separated a heavy dump of Seed without issue. Two build details matter: leave open space above the unit so airflow stays healthy, and note that assembling it in the reverse orientation stops it from working entirely (来源 1,核查 2026-09-26).
One caveat closes it out: this tiny layout runs only on an Advanced Filter — a regular Filter cannot make it work (来源 1,核查 2026-09-26).